PHX-Series可編程交換直流電源供應器，全系列包含16個主要機種，電壓及電流涵蓋從30V/200A 到 1000V/12A，其單機的輸出功率從6kW至12kW，為了滿足更多使用者高功率輸出的需求如：車用啟動馬達、電動車輛(EV)及混合動力車(HEV)用電池模塊，PHX-Series 搭配同電壓的單機進行Master / Slave的控制，因應更高輸出功率的需求，PHX-系列機種提供10組并聯操作模式，因此本系列機種在并聯后的*大電流輸出范圍可達4000A(Example: PHX 30-400S(F)C的機種*10臺)。
PHX-Series可編程交換直流電源供應器的設計是用來滿足當今在電源半導體組件或是電源行業所使用之零件在高速應用下對V-I 特性曲線測試的需求，如車用的啟動馬達(Starter Motor)、混合動力電池模塊和功率半導體組件等，在半導體電路設計、電源模塊設計及產品檢測經常需要使用快速斜率控制的電源供應器來驗證其電子零件特性，因此PHX-Series可程序交換直流電源供應器，其內建可調上升或下降斜率，用戶可按產品各別的特性進行上升及下降斜之參數設定，以確保產品驗證之周延。由于綠能等應用之興起及日漸普級化，LED組合而成的產品應用非常廣泛，因應LED產品其電源導通瞬間所產生的突波，PHX-Series電源供應器的定電流(CC Priority)優先權模式(此為選購件)，可以讓使用者在測試時將電源供應器設定在強制定電流模式下動作，以抑制突波的產生。
該電源系列包括16個主要機種型號如下，涵蓋二個不同的輸出功率， 分別為6kW及12kW，使用者透過并聯操作時，可將機器的總體輸出功率提生至120kW( 范例: PHX 30-400FC* 10 臺可提供120kW)
PHX 30-200S(F)C, 單通道 6kW / 30V / 200A
PHX 30-400S(F)C, 單通道12kW / 30V / 400A
PHX 60-100S(F)C, 單通道 6kW / 60V / 100 A
PHX 60-200S(F)C, 單通道12kW / 60V / 200A
PHX 500-12S(F)C, 單通道 6kW / 500V / 12A
PHX 500-24S(F)C, 單通道 12kW / 500V / 24A
PHX 1000-6S(F)C, 單通道 6kW / 1000V / 6A
PHX 1000-12S(F)C, 單通道 12kW / 1000V / 12A
PHX 30-200S(F)D, 單通道 6kW / 30V / 200A
PHX 30-400S(F)D, 單通道12kW / 30V / 400A
PHX 60-100S(F)D, 單通道 6kW / 60V / 100 A
PHX 60-200S(F)D, 單通道12kW / 60V / 200A
PHX 500-12S(F)D, 單通道 6kW / 500V / 12A
PHX 1000-6S(F)D, 單通道 6kW / 1000V / 6A
Operating Mode (操作模式)
*機種名稱有”F“字樣才具斜率控制功能,此為選購功能
當機器內部的保護參數設定值被觸發時，機器的前面板將自動啟動面板鎖定功能，以避免待測體在測試的過程遭受到不必要的損壞。
Wire Connection in Series Operation 串聯操作接線示意圖
*本功能僅提供在幾種名稱有 “F”字樣
Output Specifications
Specification/Models
PHX 30-200 S(F)C
PHX 30-400 S(F)C
PHX 60-100 S(F)C
PHX 60-200 S(F)C
PHX 500-12 S(F)C
PHX 500-24 S(F)C
PHX 1000-6 S(F)C
PHX 1000-12 S(F)C
Rated Output Voltage
30V
60V
500V
1000V
Rated Output Current
200A
400A
100A
12A
24A
6A
Rated Output Power
6000W
12000W
Power Source
180 VAC to 242 VAC, 3 phases
Input frequency range
45Hz to 65Hz
Phases
3-phase, 3-wire plus ground. Neutral not used.
Input Current*1
32A
64A
Input Power Factor *2
Above 0.6
Power Efficiency *3
90% or more
Inrush Current (Peak Value)
65A
130A
Note: *1: With rated output power and rated output current *2: With 200V AC input, rated output power, and rated output current *3: With 200V AC input, rated output voltage, and rated output power
Range
0.00V~31.50V
0.00V~63.00V
0.0V~525.0V
0V~1050V
Accuracy *11
0.1% of setting + 5mV
0.1% of setting + 10mV
0.1% of setting + 0.1V
0.1% of setting + 0.2V
Resolution
10mV
0.1V
1V
Load Regulation *4
0.01% of setting + 0.005% of rated output voltage
Line Regulation *5
0.01% of setting + 0.003% of rated output voltage
Ripple (RMS value) *6
< 10 mV
< 50 mV
< 100mV
Noise(p-p value)(Typ) *7
< 100 mVp-p
< 300mVp-p
Temperature Coefficient (Typ.)
± 100ppm/°C
Transient Response Time *8
1ms or less
2ms or less
Output Response Time *9
Rising
200ms ± 20%(rated load) 200ms ± 20%(no load)
500ms ± 20% (rated load) 500ms ± 20% (no load)
Falling
200ms ± 30% (rated load) <1200ms (no load)
500ms ± 30% (rated load) <1200ms (no load)
Remote Sense Compensation Voltage (Sinlge Wire)
5V
Maximum Sink Current
1A ± 20%
2A ± 20%
250mA ± 20%
500mA ± 20%
125mA ± 20%
Residual Voltage when OUTPUT is OFF (TYP)
± 10mV or less
± 25mV or less
± 50mV or less
0.0A~ 210.0A
0.0A~ 420.0A
0.0A~ 105.0A
0.00A~ 12.60A
0.00A~ 25.20A
0.000A~ 6.300A
Accuracy *12
0.5% of setting +0.1A
0.5% of setting +0.2A
0.5% of setting +0.05A
0.5% of setting +5mA
0.5% of setting +10mA
0.5% of setting +3mA
0.5% of setting +6mA
0.1A
10mA
1mA
Load Regulation *10
0.05% of setting + 0.01% of rated output current
0.05% of setting + 0.03% of rated output current
0.05% of setting + 0.005% of rated output current
Ripple (RMS Value) *6
< 200mA
< 400mA
< 100mA
< 10mA
< 20mA
< 5mA
± 200ppm/°C
Note: *4: Measurement at sensing point for 0~100% change in rated load current (Static Load Change) *5: For ± 10% change in input voltage (Static input Change) *6: At measurement frequency band of 20Hz~1MHz (Resistance Loaded) *7: Measured with oscilloscope at measurement frequency band of 20Hz~20MHz *8: Recovery time within 0.1%+10mV of rated output voltage for 50% to 100% abrupt change in rated load current (Dynamic Load Change) *9: Time in which set voltage error is reached within 1% due to setting changes via panel operation or communication control or external analog control. *10: Current change value at the rated output current when load resistance is changed until resistance value outputs 0~rated power (Static Load Change) *11: At output open-circuit and environmental temperature 23°C ± 5°C *12: At output short-circuit and environmental temperature 23°C ± 5°C
Voltmeter
4-Digit Digital Meter
Maximum Display
99.99 V
999.9 V
9999V
Measure Accuracy *13
0.1% of reading +20mV
0.1% of reading +0.2V
0.1% of reading +2V
Temperature Coefficient (Typical Value)
Ammeter
Maximum Display *14
999.9A
99.99A
9.999A
Measure Accuracy *13*14
0.5% of reading +400mA
0.5% of reading +200mA
0.5% of reading +20mA
0.5% of reading +40mA
0.5% of reading +2mA
± 200 ppm/°C
Power Meter
9.999kW
99.99kW
Accuracy *14
Displays the multiplication value of the voltage measurement value and current measurement value.
Measurement Mode
Moving average process can be selected for measurement
*13: At environmental temperature 23°C ± 5°C *14: At stand-alone operation
Over Voltage Protection Circuit
(OVP)
0.30V~33.00V
0.60V~66.00V
5.0V to 550.0V
10V to 1100V
Accuracy *10
0.2% of setting + 50mV
0.2% of setting + 0.5V
0.2% of setting + 5V
Operation
Can select from operations below
? Output OFF by switching stop
? Input switch cut-off (Input switch cut-off turns the power supply's internal input power relays OFF.)
Over Current Protection Circuit
(OCP)
2.0A~ 220.0A
4.0A~ 440.0A
1A~ 110.0A
0.12A~ 13.20A
0.24A~ 26.40A
0.060A~ 6.600A
0.12A~ 6.13.20A
0.6% of setting + 0.5A
0.6% of setting + 1A
0.6% of setting + 50mA
0.6% of setting + 100mA
0.6% of setting + 5mA
Over Temperature Protection Circuit
? Stops switching, shuts off output, and displays alarms if the temperature of the radiating section heat exceeds 90°C due to stopped fan motor, etc.
? Welds temperature fuses, built in the Inrush Limiting Resistors, at 135°C.
Excessive Input Current Protection
50A fuse
100A fuse
100A[U1] fuse
Operational Mode Displays
All modes are displayed with LEDs
OUT ON --------------------------------------------------------------------------- Orange
CV (Constant Voltage)---------------------------------------------------------- Green
CC (Constant Current)---------------------------------------------------------- Green
PRESET (PRESET)-------------------------------------------------------------- Green
FUNC. (when setting functions)---------------------------------------------- Green
REMOTE (During Remote Operation)-------------------------------------- Green
LOCK (in Key Lock state)------------------------------------------------------ Green
Master-Slave Parallel Operation
Able to control a maximum of 10 parallel connected same-voltage model products with one master unit
Master-Slave Series Operation
Able to control a maximum of 2 series connected same model products with one master unit
---
Startup Mode
CV Priority
*Only full-featured "F" type models:
High Speed
10ms
100ms
Medium Speed
300ms
Low Speed
200ms
500ms
CC Priority
*Standard version. "S" type models:
Variable Slew Rate
*Only full-featured "F" type models: Sets the rising and falling rate for each output voltage and output current individually.
CV Slew Rate Range
0.01V/s~60.00V/s
0.1V/s~120V/s
1V/s~1000V/s
1V/s~2000V/s
CC Slew Rate Range
0.1A/s~ 400.0A/s
0.1A/s~ 800.0A/s
0.1A/s~ 200.0A/s
0.01A/s~ 24.00A/s
0.01A/s~ 48.00A/s
0.01A/s~ 12.00A/s
Sequential ON/OFF
* Only full-featured "F" type models: Output ON/OFF of multiple units can be controlled from one sequential master unit simultaneously or with time lag (Setting range: 0.00s to 99.99s for ON/OFF respectively) Note: Special cable is needed for use.
Memory
Saves and loads the set values of the voltage, current, and various functions in memories "A", "B", and "C".
Key Lock
Locks key operation at the front panel.
Variable Internal Resistance (⊿R)
* Only full-featured "F" type model
0~0.15?
0~0.075?
0~0.6?
0~0.3?
0~41.7Ω
0~20.8Ω
0~167Ω
0~83Ω
Output Voltage Control
External Resistance
0~10kΩ (B, C Curve), 0~￥Ω (A Curve)
External Voltage
0~10V DC
External Voltage (Insulation)
Output Current Control
Output ON/OFF Control
Normal
Can be controlled at external contact or photocoupler
Insulation
External contact or photocoupler
Input Cut-Off Control
Voltage Monitoring Output
10V DC output (non-isolated) accuracy: 0.5% ± 10mV
10V DC output (isolated) accuracy: 0.5% ± 10mV
Current Monitoring Output
10V DC output (non-isolated) accuracy: 1.0% ± 10mV
10V DC output (isolated) accuracy: 1.0% ± 10mV
Status Output
CV (Constant Voltage), CC (Constant Current), P-ON (Input Voltage Normal)
The 5 points: LEVEL1_ALM (OVP, OCP), and LEVEL2_ALM (Group Alarm) are outputted by a photocoupler insulated open collector.
Between each input and output, input and chassis, output and chassis:
500 Vdc, 20M? or more.
1000 Vdc, 20M? or more.
Withstanding Voltage
Between input and chassis:
1.5kV AC 1 minute
Between input and output:
3.0kV AC 1 minute
Between output chasis:
1.3kV DC 1 minute
2.4kV DC 1 minute
Relative Ground Voltage
At peak voltage value, within ± 500V (Between output and ground)
At peak voltage value, within ± 1200V (Between output and ground)
Operating Temperature
0 to 50°C
Storage Temperature
-20°C to 70°C
Operating Humidity
20 to 90% RH
Storage Humidity
Other
Do not place in cold environments, and areas with condensation or corrosive gases
External Dimensions *15 W(mm) x H(mm) x D(mm)
430 x 129 x 562
430 x 221 x 562
430 x 129 x 550
430 x 221 x 550
Max. Dimensions(mm) *16
482.6 x 149 x 637
482.6 x 241 x 647
482.6 x 241 x 637
482.6 x 149 x 625
482.6 x 241 x 625
Weight
About 24.0kg
About 43.0kg
About 22.0kg
About 38.0kg
About 20.5kg
About 37.0kg
About 40.0kg
Cooling Method
Forced cooling by fan motor
Output Terminal
Copper Bar (M12 Screw)
Copper Bar (M5 Screw)
Input Terminal
4P Terminal (M6)
Note: *15: Does not include protruding sections *16: Includes handle, dial, rubber legs, and output terminal cover [U1]Fuses fixed.
無錫聚測電子科技主要經營：直流穩壓電源、交流電源供應器、數字示波器、模擬示波器、函數/任意波形信號發生器、 數字萬用表、頻譜分析儀、網絡分析儀、數字萬用表、頻率計數器、邏輯分析儀 、安規測試儀、LCR數字電橋以及各種工具等。 我們堅持技術和服務并重的思想，遵守規范、客觀、公正、實事**的原則，信守協議，重質量、求效率。 公司經營理念：服務、品質、誠信“，以**的產品和上等的服務，滿足客戶的需求，同時注重業務拓展， 努力建立與客戶的良好的溝通，堅持以人為本，以信譽與質量求生存。 要經營品牌：美國是德科技（Keysithy）/ 美國泰克（Tektronix） /美國吉時利(Keithley )美國福祿克（Fluke）/ 美國力科（lecroy）/德國羅德與斯瓦茨（R&S）/德國德圖(testo)/ 臺灣固緯(Gwinstek) /臺灣全天（apmtech）/ 北京普源精電（ Rigol ）/常州同惠(tonghui) /深圳鼎陽(siglent) / 優利德、日本日置等。 聯系方式：徐經理：18020307895，QQ:510918582
蘇公網安備 32021402000967號
